Certifications, test reports and declarations — all on the proof hub.
Silicate Systems
Contact

Certification and proof.

Full technical data sheets for each product are on the Systems pages.

Mineral poured floors, epoxy, microcement and concrete repair

Compare the binder, the complete build-up and the published evidence before choosing a floor or a repair system.

Which mineral poured floor is an alternative to epoxy?

Eco Rapid, Eco Rapid Indu and Eco Rapid Deco are mineral poured floors with a silicate binder, rather than an epoxy resin binder. Choose the system for the substrate, traffic and finish. Compare environmental impact using the published EPDs and the material and carbon calculator; its epoxy reference is indicative, not a like-for-like project assessment.

Read technical comparison →
Silicate SystemsEpoxy floor
Binder

Eco Rapid, Eco Rapid Indu and Eco Rapid Deco use a silicate binder.

Binder

An epoxy floor uses an epoxy resin binder. Performance depends on the specified formulation.

Complete build-up

Specify preparation, primer, floor and protection for the substrate and traffic.

Complete build-up

Compare the complete epoxy system at its specified thickness, not just the resin layer.

Environmental evidence

Use the published dry-mortar EPD and the primer/coating EPD for the products each declaration covers.

Environmental evidence

Use the chosen epoxy system’s EPD with the same life-cycle modules, quantities and assessment scope. The calculator reference is indicative.

Is a mineral poured floor the same as microcement?

For those drawn to microcement’s seamless mineral aesthetic, Eco Rapid Deco offers that look in a self-levelling mineral poured floor with a silicate binder. Its published application range of 1 to 30 mm and compressive strength of approximately 40 N/mm² combine decorative freedom with documented mechanical performance. A verified dry-mortar EPD (MD-26094-EN) and product-specific EMICODE EC1PLUS licensing support specification. Eco Floor Protect can provide the protective indoor finish. Microcement is typically a thin, hand-trowelled cement-based finish; its formulation, thickness and performance depend on the selected system.

Read technical comparison →
Silicate SystemsMicrocement
System and thickness

Eco Rapid Deco is a self-levelling mineral poured floor, applied from 1 to 30 mm. It brings the seamless mineral aesthetic into a poured floor layer rather than a thin decorative coating.

System and thickness

Microcement is typically a thin, hand-trowelled cement-based finish built up in several coats. Thickness and reinforcement requirements depend on the manufacturer.

Mechanical performance

Published strength class CT-C40-F10: approximately 40 N/mm² compressive strength and 10 N/mm² flexural strength under DIN EN 13813. Decorative appearance is backed by measured performance.

Mechanical performance

Strength, adhesion and wear performance depend on the named microcement system and its complete build-up. Compare published results under equivalent test methods.

Application and protection

Self-levelling application with a silicate binder. Eco Floor Protect is a protective indoor topcoat option; preparation, primer and protection are specified for the substrate and use.

Application and protection

Hand-trowelled application, usually with successive coats, sanding and sealing. Drying times and the protective finish depend on the selected system.

Verified evidence

Eco Rapid Deco is covered by independently verified dry-mortar EPD MD-26094-EN and licensed EMICODE EC1PLUS. Evidence is product-specific; topcoats require their own documentation.

Verified evidence

EPDs and emission certificates depend on the selected manufacturer and product. Request the documentation for the complete specified system.

Which products are used for concrete floor repair?

Eco Repair fills cracks and cavities before the floor system is laid. Eco Crack Repair fills cracks up to 5 mm deep and wide. Repair and levelling serve different purposes: Eco SL Mortar is a self-levelling layer, not a substitute for assessing damaged concrete. Have the substrate and the cause of cracking checked before specifying the repair.

Read technical comparison →
INDOOR AIR EMISSIONS

EMICODE

EC1PLUS — the strictest class in the EMICODE system — licensed per product across most of the range; Eco Topcoat Mono carries EC2. This measures how little a product off-gasses into the air after installation: EC1PLUS means very low VOC (volatile organic compound) emissions, verified in an emission chamber test rather than claimed. It’s a specification requirement on most institutional and healthcare projects, and it’s about indoor air quality specifically — a separate question from embodied carbon (see Circular content and carbon reduction, below).

GEV-EMICODE EC1 PLUS — very low emission

EPD

Environmental Product Declaration

Two EPDs are verified under ISO 14025 / EN 15804.

Self-levelling range

Eco Rapid, Eco Rapid Indu, Eco Rapid Deco, Eco Terrazzo Binder, Eco Dual, Eco Screed, Eco Mortar

EPD verified
Primer / coating range

Eco Primer, Eco Hydro Glass, Eco Hydro Sil

EPD verified

COMPOSITION

VOC- and APEO-free

Declared in the technical data sheets for Eco Sil, Eco Flex All In One and Eco Shield. This composition declaration is not a drinking-water or food-contact approval.


TYPE-APPROVAL

RISE type-approval

Certificate C900385, held for a named manufacturing site, covers Eco All In One for potable-water contact per DVGW W347.


WATER CONTACT

Drinking-water and pool approval

Eco Sil carries KTW (drinking water) and KSW (pool) approval; Eco All In One carries DVGW W270 and W347. Why it matters: a damaged silicate surface doesn’t release calcium into surrounding water, unlike cement-based systems — relevant for drinking-water and process-water projects.


DECLARATION

Declaration of Performance

Signed, per product, under DIN EN 13813 / EN 1504 as applicable. Published on each product’s Systems page.


SCHEMES

BREEAM / DGNB / LEED contribution

Not a certification the floor itself holds — a contribution to specific credits (emissions, indoor air quality, responsible sourcing, material reuse, and the avoided impact of keeping the existing substrate rather than demolishing it), written per project since the applicable credits depend on the scheme version, the assessor, and the exact build-up specified.

DGNB criteria mapping

Criterion references below follow DGNB New Construction Buildings, Germany, version 2023. Danish and other national schemes can use different requirements and numbering; confirm the country, scheme and version before assessing compliance.

DGNB · ENV1.2

Material selection and local environmental impact

Product-specific safety data sheets, ingredient declarations and applicable emissions certificates support the material assessment. Check the relevant product category and every layer of the specified build-up.

DGNB · SOC1.2

Indoor air quality

EMICODE licences provide product-level emissions evidence. They do not replace the completed building's indoor-air measurements or establish compliance on their own.

DGNB · ENV1.1

Building life-cycle assessment

The two verified EPDs provide environmental data for the products named in each declaration. Use the applicable EPD, quantities and service-life assumptions in the project's building LCA; an EPD does not award credits by itself.

Product-specific documents and consultant review are required; no project credits or material quality level are guaranteed.

Test reports →

METHODOLOGY

Circular content and carbon reduction methodology

The binder is silicon dioxide activated from industrial byproducts — GGBS from steel production and fly ash from coal combustion — rather than freshly extracted raw material. That byproduct share is what the 90% circular figure counts: mass of the cured system that comes from reused streams, measured on the formula, not on a project.

Carbon reduction is calculated against Portland-cement and resin systems delivering the same build-up and thickness. Because the systems are applied directly over an existing concrete, ceramic, or screed substrate — minimum thickness varies by product and project — the demolition and disposal of the old floor drops out of the comparison as well. Measured this way, the reduction is 95%.


TEST REPORTS

Test reports

Independent lab results — distinct from the certifications above.

Abrasion resistance

Tested independently by IAB Weimar (DIN EN 13892-3 / DIN EN 13813, Böhme method):

SystemResult
Eco RapidAbrasion class A9
Eco Rapid (with SiC aggregate)Abrasion class A6
Eco Rapid InduAbrasion class A6

Chemical resistance

Tested against roughly 100 individual reagents and concentrations. As one real case: independently tested against a mixture of lactic and acetic acid at pH 3 for 70 days — the exposure profile used for sewer and agricultural environments — Eco Sil retained 98% of its compressive strength versus 81% for a commercially available sewer mortar tested under the same conditions, and showed no measurable carbonation after prolonged indoor exposure, where the comparison mortar did.

Electrostatic discharge (ESD) / volume resistivity

Tested per DIN EN 1081 and evaluated against two thresholds: BGR 132 (occupational safety, requires <100 MΩ) and DIN EN 61340-5-1 (requires <1000 MΩ). Scoped per product, not range-wide:

SystemThresholds met
Eco SilBoth thresholds — suitable for environments with the stricter static-safety requirement (electronics, cleanroom-adjacent, pharmaceutical)
Eco RapidDIN EN 61340-5-1 only
Eco ResistDIN EN 61340-5-1 only
Eco Rapid + Eco Hydro SilDIN EN 61340-5-1 only

Fire — critical radiant flux

SystemResult
Eco Primer + Eco Rapid Deco + Eco Floor ProtectASTM E648 (2025) · ≥ 1.1 W/cm² · Class I (NFPA 101)

No flame spread at the test's maximum heat flux. Tested by Centexbel, accredited lab, October 2026.

Full report (PDF)